AudioStrada is in its final testing phase and will be available soon. The test version is free to download and runs in evaluation mode.

Become a tester: free licenseBe notified
AudioStrada

Recording

Record a take

  1. Choose the track's input in its header: In 1, or In 1-2 for a stereo source. Track › Add stereo track (Ctrl+Alt+T) makes a track that records two inputs.
  2. Arm the track with its R button: its input is heard through the track and its meter shows the input level.
  3. Press record (R). Several armed tracks record together.
  4. Press Space to stop. The take is a new clip; its file goes into the project's Audio folder.

Monitoring

The speaker button beside R says when a track hears its input:

SettingThe track hears its input
Autowhile armed, as set in Preferences (always, or only while stopped or recording)
Inputalways, armed or not: to play through an amp simulator
Offnever: for direct monitoring on the audio interface

The button is lit while the input is heard. An armed track's meter shows its input level, heard or not.

Raw or processed

The Inspector's Record row says what an armed audio track records:

  • Raw: the input as it comes; its effects can still change afterwards.
  • Processed: what its effects make of the input, on a track made under it, (printed).
  • Both: the raw take on the track, and the processed one on a silent track under it.

A processed take needs the input to go through the track: its monitoring must not be Off.

Session health

While a track is armed, the transport bar shows:

  • Monitoring: how long what you play takes to reach your ears, through the audio interface and the slowest effects heard live. Set the recording latency offset in Preferences for an exact figure.
  • The audio dropouts since a track was armed.
  • The recording time left on the disk.

When the monitoring is slow, Reduce chooses an audio buffer of 64 samples and turns the low latency mode on.

Low latency mode

The stopwatch in the transport bar bypasses the effects that add more than 1 ms, except on the tracks being played, so that their latency no longer delays what you hear. The mixer shows the bypassed effects struck through. Turn it off to mix.

Metronome

The metronome button (K) clicks on every beat while playing. Right-click it, or Shift+K, for its window: a picture of the bar shows what will be heard, then volume, sound, clicks per beat, accents, groups for odd meters (7/8 as 2+2+3), clicking only while recording, a count-in and a pre-roll of up to four bars. Before recording, the count-in clicks its bars first, even with the metronome off and at the song's start; then the pre-roll plays bars of the song before where recording starts. Default settings brings back those of a new project. The click is never exported.

Punch and loop recording

  • Punch (P): Shift-drag in the ruler sets the punch range, or right-click the ruler. Recording only happens inside it, so that a mistake can be replaced without touching the rest.
  • Loop recording: with the loop on (L), each pass becomes a take.

Takes and comping

Each audio take is kept whole in a lane of its own under the track, named after its number and the marker it starts at (Chorus · Take 2). What the track played before its first take gets a lane Before recording. The track plays the comp, the last take at first; the lanes show once there is a choice.

  • Drag on a lane to comp that part in, or click a take to comp all of it. Use comps the whole take. Short crossfades smooth every edge.
  • The ✕ deletes a lane; what the track plays of it stays.
  • Click the stars to rate a take. A ! says the input clipped or the audio dropped out while it was recorded; dropouts are marked in red on the clip.

MIDI loop recording merges its passes into one clip.

Recording MIDI

Enable your MIDI keyboard in Preferences › MIDI. Arm an instrument track and play: recording creates a MIDI clip. An instrument track armed for MIDI never hears the audio inputs.